Home > Compaq Proliant > Compaq Proliant 1850r Drivers

Compaq Proliant 1850r Drivers

Under the 'image=' section, the root parameter should look like: root=/dev/ida/c0d0p# (where # is the actual partition number of the root directory). Next Previous Contents privacy statementlegal notices Important: The server will fail to reboot if you fail to modify the lilo.conf file. Reboot the server. this contact form

Write down the / (root) partition device number. Usually, the size of the swap is 2X the system RAM (2 GB max!). Select Auto Probe for Hardware Devices to assist you with what hardware modules to load. See section 3.1 for SmartStart setup. click for more info

Select Auto Probe for the video card.This assists you with which video driver to load. Warranty status: Unspecified Check warranty status Drivers & software Help Knowledge base options Search HPE Support Center - HPE Most viewed solutions Advisories, bulletins & notices Manuals Troubleshoot a problem Setup & Select Install LILO on TARGET Partition (example /dev/sda1) at the Linux Loader screen to preserve the Compaq System Partition.

Starting with a system erase ensures you begin the installation process from a known non-configured state. After installation, use the patch to gain access to the secondary PCI bus. (2) ProLiant 3000 You must have the 12/30/99 ROM or later installed before the Linux installation. (3)ProLiant ML350 This is the information from step 7.a. for the / partition to utilize the remaining disk space.

Servers marked with an asterisk have special instructions as described further below. Check Use linear option. Set up the network. have a peek here This allows you to keep Compaq System Partition.

Press Enter when prompted to enter the parameter for the NIC. ftp ftp.calderasystems.com/pub/updates/eServer/2.3/018/RPMS/linux-kernel-binary-2.2.14-3S.i386.rpm Download all of the new RPM. Caldera now provides an updated installation diskette plus an updated kernel. If you choose not to create or keep this partition, floppy disks containing the utilities may be made from the SmartStart CD-ROM.

Skip step #18. you could check here Sign-in Register Site help Skip to ContentSkip to FooterSolutionsHybrid IT with CloudMobile & IoTIT for Data & AnalyticsPublic SectorService ProvidersSmall & Midsize BusinessFinancial ServicesHealth & Life SciencesManufacturingTelecommunications All Solutions ServicesAdvisory and Start with a System Erase. Select Default Kernel (386 or newer) at the Select a Kernel Screen.

Usually size of swap is 2X the system RAM (2 GB max!) Create the / partition (root partition). weblink Create the / swap partition (+500M). Select the installation packages. Servers marked with an asterisk have special instructions as described further below.

DO NOT edit or delete the Compaq System Partition. For the SCSI model, no parameters are needed. - OR - For the 20GB ATA-100 drive model: Type linux hde=2586,240,63 at the initial boot: prompt. See section 5 for more information. navigate here Type lilo at the prompt.

When using SmartStart 4.60 or earlier select UnixWare2 SmartStart configures your server hardware including options, such as an array controller, if present. Compaq recommends that you begin with SmartStart when installing Linux on a ProLiant system. Always try to use the latest version of SmartStart with your installation.

Please read section 2.1 regarding the Linux kernel and the peer bus architecture before installing Caldera eServer 2.3.

Select the video card discovered by Auto Probe. Reboot the server. Create the partitions using CFDISK or FDISK. The partition contains SmartStart diagnostic tools and is required to run the tools from the SmartStart CD-ROM.

Continue with steps #8 through #11. (4) ProLiant 6400R Follow steps #1 through #7 above. Insert the peer bus bootable diskette and Caldera eServer 2.3 when prompted. Compaq recommends you create the partition to facilitate system configuration. his comment is here Select Run System Erase Utility from the Main Menu --> Yes.

Note: For a list of known problems and their solutions, check Red Hat's errata for updates: http://www.redhat.com/errata. 3.4 TurboLinux 6.0 and 6.0.5 Hardware These installation instructions apply to the listed servers. See Section 3.1 before proceeding with these instructions. Type linux pci=irqrt at initial boot: prompt. Go to Main Menu by selecting Back.

Continue with steps #6 through #20. 3.3 Red Hat 6.2 and 7.0 Hardware These installation instructions apply to the listed servers. Integration Management features extend the benefits of SmartStart and facilitate consistency and reliability of server deployment and maintenance. Select Linux in the Operating System Selection Screen. Reboot the server after the installation completes.

Create a boot disk when prompted (you might need it later). Note: You may download this file directly later if you will have a direct connection to the Internet. Log on to the server after the installation completes. Usually size of swap is 2X the system RAM (2 GB max!).

Format the partitions. Please consult the SmartStart documentation for further information. If the SCSI driver fails to install: Select More Modules. Disable the serial service.

If you prefer to put LILO in the master boot record, you can set up LILO such that it will boot the Compaq partition using LILO mechanisms instead of the F10 Insert TurboLinux 6.0 CD-ROM, or later, when prompted.