Home > Compaq Proliant > Compaq Proliant 1600 Drivers Download

Compaq Proliant 1600 Drivers Download

Start with a System Erase. Note: You may download this file directly later if you will have a direct connection to the Internet. Note: Do not create a /boot partition. You may need to know the root partition device number for later use. this contact form

Select the installation packages. Continue until the screen prompts you for the appropriate OS media. See Section 3.1 before proceeding with these instructions. Boot from the SmartStart CD-ROM. http://h20564.www2.hpe.com/hpsc/swd/public/readIndex?sp4ts.oid=257741

dd if =install.144.peerbus-243 of=/def/fd0 bs=18kNote: This command must be executed on a UNIX or Linux system.You may also do a RAWRITE.EXE on Microsoft platforms. Select the language and locale settings. Set the Compaq Array Configuration (if applicable) using the Array Configuration Utility (ACU). The kernel cannot detect devices or adapters on the secondary PCI bus and they cannot function until the kernel is patched.

The following steps are based on SmartStart Release 4.90. See section 3.1 for SmartStart setup. Currently, SmartStart only supports manual path installation of Linux. Proceed with Linux Installation.

Servers marked with an asterisk have special instructions as described further below. Compaq recommends you create the partition to facilitate system configuration. Download the updated kernel provided by Caldera available at ftp.calderasystems.com//pub/updates/eServer/2.3/018/RPMS/linux-kernel-binary-2.2.14-3S.i386.rpm to a system that is on your local network. Starting with a system erase ensures you begin the installation process from a known non-configured state.

If you choose not to create or keep this partition, floppy disks containing the utilities may be made from the SmartStart CD-ROM. Please read section 2.1 regarding the Linux kernel and the peer bus architecture before installing Caldera eServer 2.3. The partition contains SmartStart diagnostic tools and is required to run the tools from the SmartStart CD-ROM. When using SmartStart 4.60 or earlier select UnixWare2 SmartStart configures your server hardware including options, such as an array controller, if present.

SmartStart also creates the Compaq System Partition and installs the System Partition files. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00376737 This includes some integrated devices, such as the ProLiant DL360 integrated NICs. If you prefer to put LILO in the master boot record, you can set up LILO such that it will boot the Compaq partition using LILO mechanisms instead of the F10 Please consult the SmartStart documentation for further information.

Usually, the size of the swap is 2X the system RAM (2 GB max!). weblink Important: For "ROM Based Setup Utility" (RBSU) units (such as the ProLiant ML330 and ProLiant ML350), install LILO into the MBR. Select Custom (Expert Only!) at the Installation Target screen. Restart the server.

Caldera now provides an updated installation diskette plus an updated kernel. Restart the server. Select Manual Installation --> Begin. navigate here Make sure that the Bootable and Format boxes are selected.

Set up the network. Begin the installation process. Insert the peer bus bootable diskette and Caldera eServer 2.3 when prompted.

Run SmartStart on the server: Erase Utility --> Manual --> Linux OS.

See section 2.3 for tips on disk partitioning. Format the chosen partitions. Create the swap partition: Select Linux Swap from the Partition Type Section. Write down the / (root) partition device number.

You will need this file for use later. Note: If you put LILO into the MBR, you will be unable to access the Compaq System Configuration Utilities by pressing F10 during system boot up (unless your system has ROM-based Integration Management features extend the benefits of SmartStart and facilitate consistency and reliability of server deployment and maintenance. his comment is here Download the updated installation diskette provided by Caldera:ftp://ftp.calderasystems.com/pub/updates/eServer/2.3/launch/floppy/install.144.peerbus-243 Make a bootable floppy from the downloaded image:i.e.